In Linux , Mac and Windows Last updated:
Share on:
Cloudways offers managed cloud hosting for any size business to host a website or complex web applications.

Misconfigured or expired ARP cache entries in the system might be one of the reasons for network connectivity problems.

Are you aware that clearing the ARP cache in your system may fix loading problems and connectivity errors?

This article will look at how to check and clear the ARP cache in the different operating systems.

But before that…

What is ARP cache?

ARP stands for Address Resolution Protocol, which is responsible for discovering MAC addresses and mapping them to IP addresses in order to communicate successfully with other systems on the local network. This protocol works between the data link layer and network layer.

Instead of asking the router every time where the particular device is located and what its mac address is, our system would just connect using the previously resolved IP address.

When our systems find the MAC addresses for the particular IP address using ARP protocol, they will be stored in a table for future use. This table is called ARP cache. It contains a list of known IP addresses and their MAC addresses.

ARP request is a broadcast, and ARP reply is unicast.

When to clear the ARP cache?

If the IP addresses of the network-linked devices change, ARP entries can get corrupted or expired, and new entries may not always overrule the database’s expired entries.

As a result, it may impact network performance and may cause loading or connectivity problems. In this case, you can simply clear the ARP cache to resolve the issue because clearing the ARP cache will cause all of your requests to go through the entire ARP process again. During this process, the new entries will be saved in the ARP table.

Some errors may occur during the rebuilding of the ARP cache table, so deleting the ARP cache all the time is not recommended. Instead, you can also reboot your router or system to resolve the connectivity problems.

How to clear the ARP cache?

We can easily clear the ARP cache in any operating system by using the command line. Let’s get started.


Step 1: Open a command prompt and run it as an administrator.

Step 2: To view the ARP cache table, just type the following command.

arp -a

This command displays the IP addresses, and it’s associated mac addresses.

Step 3: Next, to delete the cache table, you can use netsh utility.

netsh interface IP delete arpcache

or you can simply use

arp -d

Step 4: If you want to delete any specific entry in the cache, not the whole table.

arp -d <ip-address>

Sample Output:

C:\WINDOWS\system32>arp -a

Interface: --- 0xd
  Internet Address      Physical Address      Type          a8-da-0c-e8-0e-e6     dynamic            01-00-5e-00-00-16     static           01-00-5e-00-00-fb     static           01-00-5e-00-00-fc     static

Interface: --- 0x14
  Internet Address      Physical Address      Type            01-00-5e-00-00-16     static           01-00-5e-00-00-fb     static       01-00-5e-7f-ff-fa     static

C:\WINDOWS\system32>netsh interface IP delete arpcache

You will get ‘OK’ as a response if you use the netsh utility to clear the cache table.


Step 1: Open a terminal and use the following IP utility command to clear the whole ARP table.

ip -s -s neigh flush all

Step 2: If you want to delete the ARP record for a particular address, use arp utility.

arp -d <ip-address>

Step 3: After deleting the entries, you can simply use the following command to view the ARP table in Linux.

arp -n

This command displays the whole arp table.

Sample output:

└─# arp -d

└─# arp -n
Address          HWtype         HWaddress           Flags Mask        Interface                       (incomplete)         ether       01:00:5e:00:00:fc         C                 eth0         ether       a8:da:0c:e8:0e:e6         C                 eth0

Here, you can observe the cache entry for the specific address is cleared.


Step 1: Open a terminal in your mac and use the following commands.

Step 2: To view the existing ARP entries.

sudo arp -a

Step 3: To delete the cache for a particular interface

sudo arp -d ifscope en0 

Step 4: To clear the whole cache table

sudo arp -a -d

Sample output:

$ sudo arp -a

? ( at 01:00:5e:00:00:fc on en0 ifscope [ethernet]
? ( at a8:da:0c:e8:0e:e6 on en0 ifscope [ethernet]
? ( at 01:00:5e:00:0e:16 on en0 ifscope permanent [ethernet]

$ sudo arp -a -d ( deleted ( deleted ( deleted


If you can’t ping a particular IP address in the same network even though they’re working correctly, it’s a sign that something is wrong. Your ARP cache table may need to be reconstructed again.

I hope you found this article helpful in learning how to clear the ARP cache in different operating systems.

You may also be interested in knowing how to change DNS servers for faster browsing or how to detect Rootkits in Windows, Linux and Mac.

Share on:
  • Ashlin Jenifa
    Hey there, my name is Ashlin, and I’m a senior technical writer. I’ve been in the game for a while now, and I specialize in writing about all sorts of cool technology topics like Linux, Networking, Security, Dev Tools, Data Analytics, and Cloud…

Thanks to our Sponsors

More great readings on Linux

Power Your Business

Some of the tools and services to help your business grow.
  • The text-to-speech tool that uses AI to generate realistic human-like voices.

    Try Murf AI
  • Web scraping, residential proxy, proxy manager, web unlocker, search engine crawler, and all you need to collect web data.

    Try Brightdata
  • is an all-in-one work OS to help you manage projects, tasks, work, sales, CRM, operations, workflows, and more.

    Try Monday
  • Intruder is an online vulnerability scanner that finds cyber security weaknesses in your infrastructure, to avoid costly data breaches.

    Try Intruder